Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Lakewood
When a driveway gate jams, drags, or won’t latch, you need someone who reads gates for a living. That’s all we do. Stratford Gate Repair works the Lakewood area every week, from the older ranch and split-level blocks near Belmar to the foothills lots around Green Mountain. Our technicians have up to experience, and they diagnose by system knowledge rather than guesswork. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 509-8380 and we’ll get you a free estimate.
Why Lakewood Homeowners Call Stratford Gate Repair for Gate Repair
Lakewood’s gates take a beating that a lot of other Front Range cities don’t see in the same way. We’re a dedicated gate specialist, not a fence outfit with a repair number on the side, and that matters here. We work on the brand you already have, whether that’s a Mighty Mule opener on a backyard swing gate or a DoorKing system on an apartment entrance, so the first visit is usually the only one needed to sort out what’s wrong.
We know the local ground. The clay-heavy soil in the Green Mountain and Bear Creek foothills pushes gate posts out of plumb every spring, and a repair that holds flat in Denver can fail again on a foothills lot after the next hard freeze. Our technicians brace and re-set posts with footing depths that match that reality. That local read is why so many Lakewood homeowners keep our number on the fridge.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Commercial Gate Repair in Lakewood
Commercial Gate Repair in Lakewood runs into everything from HOA-controlled entry gates to the high-cycle operators at apartments and business parks, and Stratford Gate Repair handles the full spectrum. Commercial systems live and die on cycle count and safety hardware, not just on looks. When a DoorKing or FAAC operator starts skipping, reversing on its own, or refusing to close, the issue is often in the safety loop or the control board rather than the gate itself. We test the entrapment protection, check the wiring and power run, and confirm the operator’s photocell and safety edges are doing their job, since UL 325 requires it. Expect a typical commercial repair in Lakewood to run $350-$900, set per job by the written estimate.
High-Cycle Operator Service
Operators that open dozens of times a day wear differently than a home driveway gate. We look at the mechanical stops, the limit switches, and the hinge and roller wear that high use accelerates, so the fix lasts.
Access-Controlled Entrances
Property managers and HOAs need the gate to stay secure and stay moving. We diagnose the operator, the safety edges, and the access hardware together, because a gate that opens is useless if the entry control isn’t working with it.
Iron Gate Repair in Lakewood
Iron Gate Repair in Lakewood often means a strong panel hanging off a weak hinge, and Stratford Gate Repair fixes the frame and the hardware, not just the symptom. Wrought iron is heavier than wood, so when a post heaves out of plumb the gate drags, the hinges carry more load than they were set for, and misalignment spreads. On the 1950s-70s ranches and split-levels across Lakewood, plenty of original iron gates still have rusted hardware that needs a rebuild rather than a replacement. We weld, re-set the posts, realign the gate, and correct sag so it swings clean again. A typical iron repair in Lakewood runs $200-$650, quoted before any work starts.
Welding and Rust Repair
Rust eats at the joints and lowers the frame where water collects. We weld the weakened sections and treat the corrosion so the panel stops sagging and the repair holds.
Post Re-Setting for Heavy Panels
A deep-set footing is what keeps a solid iron gate aligned. We brace the post, re-set it to proper depth, then rehang the gate and confirm the swing, with room to spare for the next freeze.
Trusted Brands We Service in Lakewood
We know the operators Lakewood gates actually run on. Our technicians are familiar with systems across the range, from entry-level residential openers like Ghost Controls and Mighty Mule to commercial-grade operators from DoorKing and Elite. That fluency is the difference between a technician who knows the brand’s quirks and one who’s reading the manual for the first time at your curb. We work on the brand you already have, and if the operator is past saving we’ll tell you straight and quote the repair rather than upselling a full system. Parts are ordered for your gate, so turnaround depends on the job and the part, and we set a realistic window up front. Call (866) 509-8380 with the brand and model and we’ll get a free estimate started.
Common Gate Repair Problems We See in Lakewood Homes
- Hinge posts heaved out of plumb after spring freeze-thaw. Clay-heavy foothills soil swells and shifts with the thaw, lifting and tilting the hinge post until the gate drags and misaligns. Most sagging calls here trace back to the footing, not the panel.
- Wind and hail torquing hinge hardware on solid-infill gates. Spring Front Range gusts and hail push hard against a solid driveway gate and bend frames and hinge plates. The heavier the infill, the more the hardware takes the load.
- Rusted original hardware on 1950s-70s gates. Older wood and chain-link gates around Lakewood often still have the original hinges and fittings, rusted and worn. In many cases the frame and hardware can be rebuilt rather than replaced.
- Operators failing safety checks after a storm. A gate that opens but reverses unexpectedly or won’t close may have a damaged safety edge or a knocked-out photocell. That’s a safety issue, not just an annoyance, and it needs a trained technician to sort out.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Lakewood, CO
Honest numbers, so you know roughly where you stand before you call. A typical hinge or post repair in Lakewood runs $180-$450. Gate realignment and sag correction runs $150-$400. Lock and latch repair runs $120-$300. Welding and rust repair on iron runs $200-$650, and commercial repair runs $350-$900. What pushes a job toward the top of a range is usually the footing work, the depth needed on a foothills lot, or operator and safety hardware that has to be replaced alongside the gate fix. The written estimate sets the final price, and you approve the quote before any work starts.
We Also Serve Cities Near Lakewood
We work throughout the Lakewood area and the surrounding Front Range, including Arvada, Denver, Westminster, and Highlands Ranch. If you’re just outside those lines, tell us where you are and we’ll let you know how we can help. Our gate repair service covers the whole metro, and our Lakewood focus means we know this ground well. Call (866) 509-8380 for a free estimate.
Serving Lakewood, CO – Our Local Coverage Area
We serve Lakewood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Lakewood
Because the clay-heavy soil under the foothills heaves with each freeze-thaw cycle, pushing the hinge post out of plumb. That spring heave is why a gate that worked all last summer starts dragging by April. The fix is usually deeper footing and a re-set post, not just tightening the hinges, and we can get a free estimate on yours by calling (866) 509-8380.
Use the operator’s manual release, which most residential and commercial systems have for exactly this. Switch off power at the breaker first, then follow the release lever or key per the operator’s instructions, and never force the gate free by hand or put yourself under a raised or loaded panel. If the release is seized or the gate still won’t move safely, stop and let a trained technician sort it out. Call (866) 509-8380.
Focus on the entrapment protection, which UL 325 requires on automatic gates. The safety photocell should reverse the gate when something breaks the beam, and the safety edges should stop it on contact – if either fails, stop using the operator until it’s checked. That’s not a DIY fix for most systems, so have a trained technician test it. Call (866) 509-8380 for a free estimate.
Most of the time it can be repaired. Wrought-iron and commercial gates usually fail at the hinge, the post, or a welded joint, not in the panel itself, and those are all rebuildable. We rebuild, realign, and weld the existing gate wherever it’s structurally sound, and only recommend replacement when the frame is genuinely failing. Call (866) 509-8380 for a free estimate.
Yes – Lakewood is a patchwork of unincorporated pockets and HOA-governed subdivisions, and gate specs and fence-height rules can change from block to block. Before work on a gate in a governed subdivision or an unincorporated lot, it’s worth confirming which jurisdiction or HOA controls your parcel, because the rules can affect what a repair or replacement has to meet. When in doubt, ask your city’s building department or your HOA. We’ll flag anything to check during the estimate; call (866) 509-8380.
Get Your Lakewood Gate Back Up and Running
Whether it’s a sagging hinge post, a wind-bent frame, or an operator that won’t pass its safety check, we’re set up to handle it. Stratford Gate Repair is gate-focused, brand-familiar, and ready to give you a straight answer and a written price. Call (866) 509-8380 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Stratford Gate Repair.