Farm & ranch
Wrought iron
Wood & steel frame
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Highlands Ranch?
Gate parts and welding in Highlands Ranch typically cost $150 to $700 for most repairs, with common jobs like hinge replacement or a simple weld repair landing around $250 to $450. A single small bracket weld can run $120 to $200, while a full operator control board replacement can reach $450 to $700 or more on commercial-grade systems. The written estimate sets the final price, and estimates are free.
Stratford Gate Repair works exclusively on gate systems: manual swing gates, slide gates, and the electric operators that drive them. That focus is why we can quote parts and welding accurately instead of guessing. Our technicians have up to experience, and we service equipment from nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your gate is stuck, sagging, or the opener has quit, one call covers diagnosis, repair, and replacement if it comes to that.
Key Takeaways
- Most gate parts and welding repairs in Highlands Ranch run $150 to $700.
- Welding and metalwork alone is usually $120 to $400, depending on the joint and metal thickness.
- Operator parts (boards, receivers, arms, batteries) are the biggest cost swing, from $90 to $700.
- We work on the brand you already have, budget or commercial-grade.
- Free estimates. Call (866) 509-8380. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Parts & Welding Cost Breakdown (2026)
Here’s how pricing breaks down for a typical Highlands Ranch gate job. These are estimated ranges for the 2026 local market. The exact price depends on your gate, the parts involved, and what we find on-site.
| Job or Part | Typical Estimated Range |
|---|---|
| Hinge replacement (per hinge, welded or bolted) | $90 – $180 |
| Latch, drop rod, or cane bolt replacement | $100 – $220 |
| Rust or stress-crack weld repair on a steel gate frame | $120 – $300 |
| Hinge re-weld and gate re-hang (sagging swing gate) | $200 – $400 |
| Slide gate roller or track repair | $180 – $420 |
| Post reinforcement or hinge-post re-anchor | $250 – $500 |
| Operator control board replacement (residential) | $280 – $520 |
| Operator control board replacement (commercial: FAAC, BFT, DoorKing) | $450 – $700 |
| Operator arm, actuator, or gear replacement | $250 – $600 |
| Safety photo-eye or loop sensor replacement | $150 – $320 |
| Battery backup replacement (Linear, LiftMaster, Mighty Mule) | $90 – $180 |
| Keypad, receiver, or remote programming and replacement | $100 – $250 |
| Full gate frame re-weld and alignment (labor-heavy) | $400 – $750 |
A few things push a gate parts and welding job up or down. Parts cost varies by brand and whether the operator is residential or commercial-grade. A Mighty Mule control board costs far less than a DoorKing access-control board, and commercial systems also take longer to diagnose and calibrate. Labor depends on whether the gate can be welded in place or has to come off its hinges. Rust in a steel gate frame means grinding back to solid metal before any weld will hold, and that takes time. On the lower end, a single hinge, latch, or small weld is a quick, clean job. On the higher end, a sagging or misaligned gate often needs hinge work, post attention, and re-welding all at once.
If your gate hasn’t been serviced in a long stretch, it’s worth reading our Stratford Gate Repair overview before you book so you know exactly what’s included.
What Affects Gate Parts & Welding Pricing in Highlands Ranch
- Gate material and frame condition. Steel frames bend, rust, and fatigue; aluminum frames don’t rust but crack differently at weld points. A steel gate with heavy rust needs more prep before welding, and that adds labor. We tell you up front if a joint is too far gone to weld safely.
- Brand and operator type. Budget residential operators (Mighty Mule, Ghost Controls) use less expensive parts. Commercial systems (FAAC, BFT, DoorKing) use higher-cost, higher-cycle components. We work on the brand you already have, so you’re never pushed into replacing a working operator.
- Manual vs. electric vs. swing vs. slide. A manual swing gate with a broken hinge is the simplest repair. An automatic slide gate with a failed roller plus a misaligned track is a bigger scope of work. Electric gate repair done right means diagnosing the mechanical side and the control side together, since a mechanical bind can burn out a control board.
- Highlands Ranch’s freeze-thaw winters. The Front Range swings between hard freezes and warm afternoons, and steel gates and their hardware feel it. Metal contracts and expands repeatedly, which loosens welds and stresses hinge pins. Gate frames and posts also shift slightly as the ground heaves. That seasonal movement is a common reason hinge welds crack and slide gates drift off track, and it’s a real factor in this market.
- Gate weight and size. A wide driveway gate takes more labor for welding because it has to come down or be braced to be worked on safely. Heavier gates also need stronger welded reinforcement, which costs more in both parts and time.
- Access and mounting height. Gates set high off the ground or tight against a fence line are harder to work around. Reach, bracing, and safety all affect labor on a weld job.
If you want a full picture of how gate work is handled in this market, including neighborhoods like Northridge and Westridge, see our Highlands Ranch service page.
How Does Gate Welding Work, and What Can Be Welded?
Gate welding covers the structural and hardware connections on your gate: hinge plates, frame joints, post brackets, mounting tabs for the operator, stop plates, and track supports. A weld repair means grinding back to clean metal, clamping the joint back into position, and re-welding it so the gate hangs true again. What can and can’t be welded depends on the metal. Steel welds cleanly. Aluminum can be welded but needs the right filler and technique. Cast iron brackets are sometimes better replaced than welded. When you call, tell us the gate material and where the damage is, and we’ll tell you whether welding is the right fix or whether a part replacement is the better call. If your gate is stuck, cracked at a joint, or the operator has pulled loose from its mounting, that’s usually a welding job and not a parts job.
One safety note worth repeating: a heavy gate that has cracked at a hinge or joint can fail suddenly. If you see a gap opening up at a weld or the gate is leaning, keep people and vehicles clear of it until a trained technician has looked at it. Don’t try to brace it yourself or weld it in place without proper equipment and eye protection; a gate panel that lets go can cause serious injury. We’d rather come out and check it than have you find out the hard way.
How Much Do Gate Operator Parts Cost?
Operator parts are the largest cost variable in gate parts and welding pricing, and they range widely by brand and cycle rating. For budget residential operators like Mighty Mule and Ghost Controls, control boards, receivers, and batteries usually land in the $90 to $280 range. For mid-range and commercial-grade operators (Linear, LiftMaster, Elite, Viking), expect $250 to $520. For high-cycle commercial systems like FAAC, BFT, and DoorKing, control boards, actuators, and safety devices commonly run $450 to $700 or more. The brand you own determines the part cost, and we carry the brand familiarity to order the right part the first time. If the diagnosis shows the operator is past repair, we quote a replacement and installation instead, and you decide from there.
How to Save on Gate Parts & Welding
- Get the free estimate before you authorize any work. A clear written estimate is the only way to know what you’re actually paying for. Call (866) 509-8380 and the estimate is free.
- Fix small hinge and weld problems early. A $120 weld repair today can prevent a $600 re-hang later. A cracked hinge weld almost always gets worse, especially through Highlands Ranch’s freeze-thaw cycles.
- Ask for the part number and brand. If you’re comparing quotes, make sure each one is priced on the same part. A cheaper quote on the wrong board doesn’t save you anything.
- Repair the operator if it’s serviceable. A control board or receiver replacement on a good operator is far cheaper than a whole new system. We diagnose by system knowledge, not guesswork, so you’re not paying for parts you don’t need.
- Keep the gate’s mechanical side aligned. Most burned-out operators trace back to a binding or misaligned gate that overloaded the motor. Addressing a stiff hinge or sagging gate early is one of the cheapest ways to protect the operator.
- Bundle parts and welding on the same visit. If a hinge needs welding and a latch is failing, one visit covers both and you don’t pay for a second trip out.
Can You Fix a Broken Gate the Same Day?
Often, yes. Many gate parts and welding jobs in Highlands Ranch are handled same-day when the right part is on hand and the damage is mechanical or structural. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday means most calls get a technician out quickly. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. If your gate can’t be made safe the same day, we’ll tell you what to do in the meantime.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Highlands Ranch?
Gate welding in Highlands Ranch typically costs $120 to $400 for a single joint or hinge repair, and $400 to $750 for a full frame re-weld and alignment. Price depends on the metal, the damage, and how much prep the joint needs. Call (866) 509-8380 for a free estimate.
Is it cheaper to repair or replace a gate?
Repair is almost always cheaper when the gate frame is sound and only hardware or a single joint has failed. A hinge or weld repair at $120 to $400 beats a new gate installation at several times that cost. Replacement makes sense when the frame is rusted through or bent beyond safe repair. We tell you which side of that line you’re on before any work starts.
How much do gate operator parts cost in Highlands Ranch?
Gate operator parts run from $90 to $280 for budget residential brands (Mighty Mule, Ghost Controls) and $450 to $700 or more for commercial-grade systems (FAAC, BFT, DoorKing). We work on the brand you already have and quote the exact part before ordering. Call (866) 509-8380 for a free estimate.
Do you work on my gate’s brand?
Yes, if it’s one of our nine: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule. We service both entry-level residential openers and high-cycle commercial operators. Tell us the brand and model when you call and we’ll confirm from there.
Can you come today?
Same-day service is common for gate parts and welding jobs in Highlands Ranch. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 509-8380 and we’ll get you on the schedule.
Does my gate need a permit for welding or repairs?
Repair and welding work on an existing gate usually doesn’t require a permit, but new gate installation or changes to a gate on a property line can. Check with the City of Highlands Ranch or your HOA before a new install, and we’ll point out what to ask about when we’re on-site.
When your gate is stuck, cracked at a joint, or the operator’s quit, one call covers it. Stratford Gate Repair is a gate specialist, not a generalist, and we’ve built our work around the systems we service. Call (866) 509-8380 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Back up and running is the goal, from the opener to the hardware.
Pricing reflects the Highlands Ranch market as of 2026. Stratford Gate Repair offers free estimates – call (866) 509-8380.
Written by the team at Stratford Gate Repair.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Ernesto Torres"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Lucia Herrera"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Eric Norris